Skip to content
Home » 01-06 Mitsubishi Montero or Galant Bracketron Phone Mount Installation Guide

01-06 Mitsubishi Montero or Galant Bracketron Phone Mount Installation Guide

December 29th, 2009 · No Comments

Installation instructions for the Mitsubishi Montero
– Locate and remove two vertical Phillips screws above the display panel. With Dash Trim Tool (#SIT-104), locate and release six (6) clips that secure the trim bezel. Remove bezel and disconnect emergency flasher wiring harness from the back of the bezel. Set bezel aside carefully.
– Locate and remove the two (2) screws from the right side of the radio. Set screws aside in safe place. Place smaller part “A” over the original screw holes as shown in top picture and replace factory screws.
– Connect emergency flasher wiring harness and reinstall dash bezel making sure all six (6) clips are secure. Replace the two (2) factory screws and control knobs. Once bezel is completely secure, connect larger part “B” to smaller part “A”. Use hole pattern (3) for the Mitsubish Montero.
– Use the two (2) provided cap nuts and tighten part “B” to part “A” with a 5/16” open end wrench.Install any Bracketron phone holder or Amps compatible device to your Bezel Mount. Your installation is complete.

Installation instructions for Mitsubishi Galant
– Use the Dash Trim Tool (Part #SIT-104) to remove the main dash bezel. Start in the lower right corner of the dash bezel and release a clip. – Continue by releasing three (3) more clips in each corner of this bezel. Set this bezel aside carefully.
– Locate and remove the two (2) screws from the right side of the climate control. Set screws aside in safe place. Place smaller part “A” over the original screw holes as shown in bottom center picture and replace factory screws.
– Reinstall dash in reverse order securing all clips. Once bezel is completely secure, connect larger part “B” to smaller part “A”. Use hole pattern (3) for the Mitsubish Galant. Use the two (2) provided cap nuts and tighten part “B” to part “A” with a 5/16” open end wrench.Install any Bracketron phone holder or Amps compatible device to your Bezel Mount. Your installation is complete.

Download

Related Post

  • 2004-2006 Nissan Maxima Bracketron Phone Mount Installation Instructions
  • 1992-96 Dodge Stealth Pro.Fit VSM Kit Installation Instructions
  • 1998 Dodge Ram Pickup Pro.Fit Kit Installation Instructions
  • 2001-2003 Nissan Infiniti QX4 See Reverse Side Installation Instructions
  • 1995-99 Nissan Maxima Pro.Fit VSM Installation Instructions
  • 1994-95 Dodge Caravan, Plymouth Voyager Chrysler Town & Country Pro.Fit Instructions
  • 1997-98 Nissan 200SX, Sentra Pro.Fit VSM Kit Installation
  • i-Mazda-R DICE iPod Integration Kit Mazda Radio Interface Kit
  • 1995-2001 Mazda Millenia Pro.Vit VSM Installation Instructions
  • 2003-2005 Mazda 6 Dash Disassembly Installation Instructions

Related Tags: bezel, bottom center, bracketron, cap nuts, climate control, compatible device, control knobs, emergency flasher, galant, hole pattern, mitsubish, mitsubishi galant, mitsubishi montero, montero, phillips screws, radio set, safe place, screw holes, set screws, wiring harness

Search engine terms: installing a prostart car starter in a 2006 dodge magnum, pics of wiring a prostart in 2001 dodge caravan, , , wiring prostart in 2001 dodge caravan, bracketron mazda 3, installing double din screen in e46 bmw, pro start installation, , , spark plug torque lancer, prostart installation, diagrama alarma spyder, remove bmw 328i din, car stereo antenna cable, remove bmw 328i stereo, prostart installers, bravotub com, subaru belt housing face plate, mw e36 borla exhaust,

Leave a Reply

Your email address will not be published. Required fields are marked *